Ventura V2 PM SoftCam
Thanks to the revolutionary and innovative development of the Virtual Cam, the V2-PM SoftCam is the only CNC machine on the market that can reach the same cycle times as a cam machine
This machine is the evolution of the V2 SoftCam equipped with an axially mobile counter-clap. This execution is necessary when the material is tenacious and the chips are difficult to evacuate. It also allows the detachment of rivets and similar parts that cannot be ejected through the counter-clier.
The advance and clamp clamping are controlled by a secondary virtual cam.
The V2-PM SoftCam CNC is no longer dependent on the interpretation of a language, line by line, but runs several virtual cams simultaneously. All movements made by the mobile counter-clap can be performed simultaneously with the turning and cross-section movements). This revolutionary approach allows the machine to achieve much faster production cycles than comparable CNC machines.
The SoftCam control allows very fast and very simple programming thanks to optimized pictograms and diagrams. Each operation can then be corrected individually, very easily by the operator. SoftCam can be assimilated by all operators in a few hours.
Compared to a cam machine, the SoftCam CNC control allows flexibility and productivity optimization without wasting time.
- Simple and complex parts
- Material in crowns
- Material diameter from 0.3 mm to 5 mm (maximum in mild steel)
- Turning operations with two tools
- Possible operations in follower mode (mobile counter-clap depending on the material)
- Possible work without form tools
- Continuous work 24 hours
- Simple and fast gear-up thanks to SoftCam
- Easy adaptation of the production process
- Very effective when the material is stubborn and the chips are difficult to evacuate.
- Allows the unsetting of rivets and similar parts that cannot be ejected through the counter-clap.
- Optimization of production cycles thanks to the SoftCam system, allowing better accuracy and longer tool life.
- Efficient and economical production of simple parts with short production cycles.
- Training and driving simplified by the elimination of cams.
- Same chuck as on FlexCam machines with the possibility (optional) of mounting a chuck at 10,000 or 12,000 rpm.
- Reduction in the cost of material by significant reduction in falls.
- Descolleted parts without nipple, hence the elimination of an expensive recovery.
- Production stoppages due to the load are more spaced.
- Since the piece is better supported, the advances for diving operations or cutting can be stronger.
- The pieces can be ejected through the counter-clip or, when its length allows it, forward.
- Reduction of manufacturing costs by the reduced size of crunn machines (compact design).
- Reduction of labor thanks to the feeding of machines (material loaded by crown) at longer intervals, real continuous work 24/24h. The operator has the necessary time to drive more machines.
- Production stoppages due to the load are more spaced.
Ventura V2 PM SoftCam
Thanks to the revolutionary and innovative development of the Virtual Cam, the V2-PM SoftCam is the only CNC machine on the market that can reach the same cycle times as a cam machine.
This machine is the evolution of the V2 SoftCam equipped with an axially mobile counter-clap. This execution is necessary when the material is tenacious and the chips are difficult to evacuate. It also allows the detachment of rivets and similar parts that cannot be ejected through the counter-clier.
The advance and clamp clamping are controlled by a secondary virtual cam.
The V2-PM SoftCam CNC is no longer dependent on the interpretation of a language, line by line, but runs several virtual cams simultaneously. All movements made by the mobile counter-clap can be performed simultaneously with the turning and cross-section movements). This revolutionary approach allows the machine to achieve much faster production cycles than comparable CNC machines.
The SoftCam control allows very fast and very simple programming thanks to optimized pictograms and diagrams. Each operation can then be corrected individually, very easily by the operator. SoftCam can be assimilated by all operators in a few hours.
Compared to a cam machine, the SoftCam CNC control allows flexibility and productivity optimization without wasting time.
- Simple and complex parts
- Material in crowns
- Material diameter from 0.3 mm to 5 mm (maximum in mild steel)
- Turning operations with two tools
- Possible operations in follower mode (mobile counter-clap depending on the material)
- Possible work without form tools
- Continuous work 24 hours
- Simple and fast gear-up thanks to SoftCam
- Easy adaptation of the production process
- Very effective when the material is stubborn and the chips are difficult to evacuate.
- Allows the unsetting of rivets and similar parts that cannot be ejected through the counter-clap.
- Optimization of production cycles thanks to the SoftCam system, allowing better accuracy and longer tool life.
- Efficient and economical production of simple parts with short production cycles.
- Training and driving simplified by the elimination of cams.
- Same chuck as on FlexCam machines with the possibility (optional) of mounting a chuck at 10,000 or 12,000 rpm.
- Reduction in the cost of material by significant reduction in falls.
- Descolleted parts without nipple, hence the elimination of an expensive recovery.
- Production stoppages due to the load are more spaced.
- Since the piece is better supported, the advances for diving operations or cutting can be stronger.
- The pieces can be ejected through the counter-clip or, when its length allows it, forward.
- Reduction of manufacturing costs by the reduced size of crunn machines (compact design).
- Reduction of labor thanks to the feeding of machines (material loaded by crown) at longer intervals, real continuous work 24/24h. The operator has the necessary time to drive more machines.
- Production stoppages due to the load are more spaced.
Get in touch with us.
If you have any questions, or would like a quote please call 603-524-0082, or leave us a message by filling out our contact form. You can also send us and email if you prefer to info@swissettool.com.